Which Lube Should You Use?

Avatar photo

The business of keeping the brakes dry and the wheels attached is a challenge, for sure, but some fleets say it’s routine, no matter which seal or bearing lube you use. You just have to keep things clean during installation, fill the hub with lube properly, and drive the new seal in accurately. For some maintenance shops, there’s just no reason to alter the tradition of using a gear-oil lubricant, commonly an 80W90 grade. But for others, it’s been a different story altogether.

Many fleets have shifted away from oil as their wheel-end lubricant of choice toward a higher-viscosity semi-fluid grease, both mineral-based and synthetic. And many of them are happy to be done with the leakage issues that oil seemed to create. Some say leakage is gone entirely and wheel-end failures are down by 75% or more.

Fleets began switching from oil to semi-fluid grease lubricants with a vengeance in about 1995, though some of those greases have been on the market since 1987. At a meeting of The Maintenance Council (TMC) of the American Trucking Associations several years ago, one carrier’s maintenance chief described his success with the switch, and that effectively lifted the flood gates. Tired of dealing with leaking wheel seals, many others followed his cue.

As well as ending leakage, these semi-fluid greases were also said to offer longer seal life, superior suitability to temperature extremes (which is open to debate, some say), extended service intervals (also open to debate), and of course elimination of brake-shoe contamination. But they also add a new twist.

“With an inadequate amount of semi-fluid lube, we began to see a lot of bearing failures on the tapered-spindle designs,” explains Mark Wagner, hub product manager at Consolidated Metco Inc. in Portland, Ore., “because the small end would be starved of lubricant.

“So this is the issue. Now that we have converted a lot of people to semi-fluid lube, they’re experiencing a significant number of more serious types of failure.

“The failure mode has changed. The failure mode is no longer oil leaking from a seal; the failure mode will be a bearing that fails, and this difference has been difficult for people to live with.” Some fleets using semi-fluid grease have seen early failures-including wheel-offs-on trailer axles in just a few hundred clicks or as far out as 200,000.

They might find rust on the outer end of the axle spindle, on the bearing-adjustment nuts, and even on the outer bearing itself.

There may be evidence of excessive pressure and moisture in the hub assembly, the latter often caused by high-pressure washing of the wheel-end components.

There have been reports of sufficient rusting or excessive heat, or both, to cause the elements of the outer bearing to seize together.

“In many of the reported failures, there are indicators of poor lubrication of the outer bearing in a tapered-spindle application. This is evidenced by heat discoloration of the bearing elements and spinning of the inner bearing race or the bearing cup in their respective journals,” says Rolf VanderZwaag, maintenance and technical advisor to the Ontario Trucking Association.

“Spindles that use inner and outer bearings of the same dimension have been identified as not being prone to failures associated with the use of semi-fluid lubricants.”

You can spot lube contamination, VanderZwaag says, by looking for discoloration of the lubricant or a change in its consistency, especially outside of the outer bearing. You might also see changes in the appearance of the inner surfaces of aluminum hubcaps.


There are two key issues with the grease option, says Nicolas Samman of Petro-Canada Lubricants in Mississauga, Ont. One is contamination by the entry of water and dirt through the hubcap vent, with the result that rust and debris migrate to the outer bearing and bring failure. The other issue, and it’s the more critical one, is confusion as to what constitutes the correct fill level.

How much is enough? And how do you know how much lube is in there?

“Many of the problems involved with failures on the road today are related to the process of installing lubes into the system,” agrees Con Met’s Wagner. “Especially the semi-fluids, where it’s very difficult to monitor the amount you’ve installed.

“And it’s also important to know where it is in the hub. You have some segregation of areas in the hub that can mean the outer bearing is blocked off from the centre portion of the hub, or the grease cavity as we call it. And then there’s a region near the seal. A semi-fluid lube, when it’s hot, can migrate between these bearings but it doesn’t do so readily.

“I’ve seen many bearings that have a lower level of fill, where the hubcap remains completely dry inside, so no lube is ever getting out there.”

Recommended fill levels usually refer to percentage of fill, but that can be tough to communicate to service personnel who are used to dealing with static fill-level indicators like those used for oil. And if fill levels are to be determined as a percentage of the volume of space within the hub, then technicians need to know more. If they don’t know the cavity’s volume, then they’ll either work blind or ask, reasonably, “Percentage of what?”

“A fill-quantity recommendation would be more useful, either by weight or by volume, but this often requires taking into account a residual quantity of lubricant remaining in the hub,” says VanderZwaag.

Mobil’s recommendation had been a 30% fill, but that’s changed to 40% to 50% with tapered bearings. TMC’s advice, part of Recommended Practice 631 presently being revised (see sidebar, below), is 50%.

There’s another view on the fill question, and it’s an interesting one, from Jon Cox, vice-president of product engineering at Stemco Inc. in Longview, Tex. He doesn’t necessarily agree that the culprit is the fill level.

“That’s what we’ve been told by the industry,” Cox says. “But what I have not seen, as an engineer, is a complete and thorough root-cause analysis to find out if that really is the root cause. I’m not sure if it is. There are people out there who say they filled their hubs appropriately and they still had burn-up issues.

“So the question that I have is, do we really know what happens as far as wheel-end burn-ups are concerned, or are we just blaming it on the trailer manufacturers?”

At this point, there’s no answer to his question.


Nor is there a totally straightforward answer to the question as to which lubricant is best suited to wheel-end duty. There are three basic choices: an oil, almost always an SAE 50 synthetic transmission fluid; a semi-fluid grease, either synthetic or mineral-based; or a #2 grade grease, which is similar to chassis lube.

We haven’t discussed the latter solid grease, but there are those who consider it the optimum wheel-end lube in some situations. The chief benefit is that it stays put, won’t migrate away from the bearings, and it certainly won’t leak. But it demands a very different fill procedure, and its cold-weather performance demands a careful spec’ing approach because some such greases will not bleed oil readily at low temperatures.

The downside with semi-fluids, as we’ve covered, concerns their fill and inspection procedures for the most part. As good as they might get, they’ll never be as easy to deal with as oil.

And as lubricant engineer Bob Tanis of Henkel Lubricant Technologies in Cincinnati, Ohio, points out, if semi-fluid lubes demand as much installation and inspection rigor as seems to be the case, then their initial low maintenance promise is in question. Tanis chairs TMC’s RP 631 Task Force. In fact, there’s no broad agreement that any one lube is the best option. Samman says semi-fluids are “the more forgiving lubricants,” but the trend toward their use was a matter of seal reliability, not an issue with oil itself.

And now that a great deal of development work has led to improved seal technology, oil may be poised to make a comeback. Some say it’s the best choice; others, including Wagner, disagree. His vote goes to grease, with qualifications.

Tanis has another theory on the switch to semi-fluids. “I think the reason that grease was given any credence at all was the fact that the seal manufacturers were under the very strong opinion that truckers would not pay for a better seal,” he says.

“Really, they took a step back in lubrication technology by 30 years. In the 1950s, they came out of grease and went to an oil and thought it was wonderful. Now we’re saying ‘grease is better’? I guess I still have a question about that.”

So does Jon Cox of Stemco, though he won’t make specific recommendations.

“I believe the simplest, most cost-effective lubricating means is still oil,” he says. “It’s very easy to install, and most importantly it’s verifiable. That is becoming more and more an issue out there. As people go to higher-viscosity lubricants, now they find they have a lack of confidence as to whether or not they have enough in there.

“But our products are designed to work with any type of lubricant,” he adds. “If the fleet wants to use lubricant ‘A’ versus lubricant ‘B’ or lubricant ‘C’, we need to seal it reliably, regardless of its consistency.

“From about 1995, we had significant growth in the use of semi-fluid lubricants, but I personally think that the growth has stopped. I’m not saying that’s good or bad, just that it appears that other componentry such as the seals, and the installation practices, are now of a quality that people no longer need to use a more expensive, more exotic lubricant.”

It may be, however, a matter of choosing the right horse for the course.

“We don’t think there’s one lubricant for everybody,” says Mark Wagner. “To choose the optimum lube, you have to look at your maintenance and service environment, also at your application. There are cases where you’d want to have the flag, the warning of leaking oil, to try to minimize any further damage.”

Wagner also points out that severe-duty situations lend themselves to the use of oil and simpler seal technology because there’s already a lot of maintenance being done and long seal life isn’t a factor.

Both he and Cox talk about the prospect of million-mile seals, but while Wagner figures that grease technology will be necessary in that case, Cox says it isn’t yet obvious.

Regardless of the lube to be used, that “dream seal” isn’t far away.

“I think we’re going to continue to see new innovations in the wheel end as the industry tries to benchmark up to that million-mile mark,” says Cox. “We hope to get there in about two years.”

Avatar photo

Rolf Lockwood is editor emeritus of Today's Trucking and a regular contributor to Trucknews.com.

Have your say

This is a moderated forum. Comments will no longer be published unless they are accompanied by a first and last name and a verifiable email address. (Today's Trucking will not publish or share the email address.) Profane language and content deemed to be libelous, racist, or threatening in nature will not be published under any circumstances.