Truck News


Five brake tips for Brake Safety Week

ELYRIA, Ohio — Brake Safety Week is approaching Sept. 7-13 and with that in mind, Bendix has assembled a list of five need-to-know tips to help ensure fleet operators stay in compliance.

Brake Safety Week, also known as Operation Airbrake, is a Commercial Vehicle Safety Alliance (CVSA) initiative. Since the program was launched in 1998, more than 3.4 million brakes have been inspected. This year, CVSA inspectors are expected to conduct more than 30,000 roadside checks during Brake Safety Week.

“Regular, thorough vehicle maintenance – including using replacement parts designed to meet or exceed today’s regulations – along with pre-trip inspection practices, are a vital part of improving roadway safety, and Bendix shares CVSA’s commitment to promoting their importance,” said Fred Andersky, Bendix director of government and industry affairs. “The upkeep and training practices emphasized during Operation Airbrake need to be part of everyone’s year-round planning and operations.”

Here are five tips from Bendix on ensuring Brake Safety Week goes smoothly:

What to do with an out-of-adjustment brake stroke: Wheel-ends beyond the maximum allowable brake stroke are considered out of adjustment, and drivers can incur fines if 25% of a truck’s wheel-ends are out of adjustment. The most crucial advice for fleets and drivers operating vehicles with automatic slack adjusters is not to manually adjust the ASA if the brake is beyond the stroke limit. Several factors can cause a brake stroke to exceed the maximum allowable value, including improper lubrication of the camshaft, cam tube, and clevis pins; or excessive wear of the cam head, bushings, and rollers. None of these are fixed by manual readjustment of an automatic slack adjuster.

How to keep the air system clean: Contamination – and oil, in particular – can contribute to premature damage of key components such as brake modulating valves and brake chamber diaphragms. And oil-deteriorated seals can cause air system leaks, which are a target of Operation Airbrake inspections. Monthly checks for moisture in the air brake system, along with installation and regular replacement of oil-coalescing air dryer cartridges such as Bendix PuraGuard will help ensure proper operation of the air brake system.

How to read and address fault codes: A commercial vehicle’s dashboard ABS (Anti-lock Braking System) warning lamp conveys information on problems with the ABS system, such as wheel speed sensors, while the traction control/stability control lamp provides information regarding the traction control and stability systems (if the vehicle is equipped with these systems). The blinking light fault codes for both systems are accessed using the dashboard diagnostic switch or a remote diagnostic unit. By referring to the fault code information in the service data sheet, a driver or technician can pinpoint and repair specific sensor issues.

How to conduct effective visual inspections: Pre-trip inspections are the first level of vehicle maintenance and are essential to brake system safety and performance. Drivers should walk around the vehicle and look for obvious problems such as loose hoses and leaks, and check air disc brake rotors for cracks. For drum brakes without dust shields installed, this is a good opportunity to check the lining wear, which can be done without removing the wheel. It’s not necessary to get under the vehicle before every trip; once or twice a week should suffice.

The condition and quality of brake friction: Inspect brake linings for thickness, cracks, and wear – all of which affect stopping power and CSA scores.


Truck News

Truck News

Truck News is Canada's leading trucking newspaper - news and information for trucking companies, owner/operators, truck drivers and logistics professionals working in the Canadian trucking industry.
All posts by

Print this page
Related Articles

1 Comment » for Five brake tips for Brake Safety Week
  1. Nick Reeves says:

    Brakes get out of adjustment,in normal driving and braking you mostly are just feathering the brakes to slow down, so auto slacks can’t keep the adjustment in place. when I get stopped for level one inspection,I make three full brake pedal applications, this will set up all the auto slacks, to the right amount of travel(approx 2 inches) if a slack isn’t working properly this will show up now. Before making these three applications ensure that the maxi’s are off.

Have your say:

Your email address will not be published. Required fields are marked *