Keep the spring in your air suspensions

Avatar photo

Air springs are such simple and reliable components, it’s easy to overlook them during preventive maintenance inspections. Short of a rupture, hardly anything ever goes wrong with them. If they appear to be intact and holding air, what else would you need to worry about?

They actually deserve more attention than they get.







During a visual inspection, mechanics should check for signs of irregular wear, such as abrasion or cuts on the rubber portion of the air spring. It is also important to inspect the air spring for a buildup of foreign materials, ensuring everything is clean and clear of debris.

Foreign material like pebbles, chunks of road salt, and other debris can lodge in the space where the rubber flex member wraps around the pedestal, causing rubber abrasion. Left unchecked, this can eventually wear a hole in the material, causing the spring to deflate.

“In areas where road salt is used, any piece stuck on the pedestal can create friction with the flex member and begin premature wearing of the flex member,” says David Brinkman, director – air springs at Stemco. “Higher performing air spring manufacturers use some type of corrosion-resistant coating, but if there are signs of impact from road debris, these chemicals can begin deteriorating the unit. As well, chemicals used for road surface treatment in winter conditions can negatively impact an air spring, particularly an alloy piston or top plate.”

In 2015, Stemco acquired the manufacturer of Goodyear air springs, as well as Super Cushion and Spring Ride air springs, from ContiTech, a division of Continental Corporation.

A visual inspection of the air spring should include the bead plates, the flat metal plates attached to the rubber portion of an air spring, to ensure the parts are not bent or convex.

“If the bead plates are bent, this could be a sign of overextension from a worn shock absorber or incorrect ride height,” cautions Mark Hilburger, executive director of marketing for air spring manufacturer Firestone Industrial Products. “Mechanics should ensure the mounting hardware is securely fastened and that there is no contact between the air line and the outside diameter of the air spring, as contact with the air lines can cause damage to an air spring.”

There are a few mechanical issues, more with the truck than the air spring, that also need to be checked. A vehicle’s ride height, for example, can affect the life and performance of an air spring.

Drivers will occasionally tamper with the ride height adjustment to make the truck “ride better”. Ensure it’s set to factory settings.

“If the ride height has been set improperly based on specifications by the original equipment manufacturer, the air spring will not function as intended,” says Hilburger. “This can cause the air spring to frequently hit the internal bumper if the ride height is too low, or it can cause the bead plate to deform and leak from overextension of the air spring if the ride height is set too high. Improper ride height can also limit the life of the air spring.”

It’s not uncommon to see some misalignment cause the air springs to become cocked to one side.

“This can lead to an uneven load on the suspension, which can cause premature failure through overload on one side of the truck/trailer and over-extension on the opposite side,” says Brinkman. “This can occur with the misalignment of the suspension, but also if two different manufacturers air springs are used that have slightly different ride height specifications.”

Speaking of replacing springs, it’s a good idea to focus on like-for-like replacements to maintain performance and the expected life of the air spring.

“We have seen other manufacturers that provide an air spring that will fit into an existing application, but these parts may not have the same load carrying capacity or stroke length,” says Hilburger.

Most of the time, you’ll never need to give your air springs a second thought. Keep it that way by have a close look at them every couple of months. They are simple and reliable parts, but they’re mission critical, too. If an air spring isn’t working, neither are you.

Avatar photo

Jim Park was a CDL driver and owner-operator from 1978 until 1998, when he began his second career as a trucking journalist. During that career transition, he hosted an overnight radio show on a Hamilton, Ontario radio station and later went on to anchor the trucking news in SiriusXM's Road Dog Trucking channel. Jim is a regular contributor to Today's Trucking and Trucknews.com, and produces Focus On and On the Spot test drive videos.


Have your say


This is a moderated forum. Comments will no longer be published unless they are accompanied by a first and last name and a verifiable email address. (Today's Trucking will not publish or share the email address.) Profane language and content deemed to be libelous, racist, or threatening in nature will not be published under any circumstances.

*